Whether you use a boiler or furnace heating system, you will experience several issues with your system after a certain period. When this happens, the first thing that might come to your mind is to call an oil Furnace & Boiler Repair service provider like JetAirCo. As one of the leading Furnaces and Boilers system providers in the regions of Hauppauge, Smithtown, Northport, and Long Island, located in New York, USA, JetAirCo’s professionals are always available to handle Oil Burner Service quickly, Boiler repair service, Furnace Repair Services, and Boiler Installation issues. Therefore, you can rely upon us at any time of the day.

But do you know? There are specific tasks that you can perform on your own. Here, for your help, JetAirCo’s professionals come with some pocket-friendly steps that you can attempt to prevent the costly repair cost.

Step 1:- Completely Shut Down your System

Before you move further, first ensure that your heating system is turned off completely. Hence, switch off the fuel/boiler electrical power and fuel supply. This way, you can protect yourself and perform any heating system maintenance and repair.

As per JetAirCo Gas Furnace Repair Services, you will see the electrical power switch at the top of the cellar stairs or the bottom. Locating it will be easy as the electrical power switch comes with bright red color light.

Step 2:- Take Out Loosen Particles & Carbon Soot

After successfully turning off the heating system, you should take out loose particles and debris from the heating system’s combustion chamber. Remember that the procedure might take some time; however, you need to repeat the step until you completely remove carbon dioxide, water vapor, carbon soot, and other debris from the combustion chamber.

Cleaning the heating system combustion chamber will stop debris build-up on the chamber wall or any other area.

Step 3:- Inspect the Flue Pipe

To make sure your heating system’s combustion products exit from your place correctly, give special attention to the flue pipes. Besides, with It, you will quickly determine any leaks, holes, or cracks.

Hence, thoroughly inspect the flue pipe. Precisely where the lines meet the heating system. In case you experience a small leak or hole, you can wrap it with foil tape for a temporary solution. However, large leaks or holes require professional experts such as JetAirCo Heating System Repair Services.

Step 4:- Change the Oil Filter

Have you remembered when you last replace the oil filter of your heating system? No? Then instantly purchase a new oil filter and replace it with the existing one. Remember that replacing the oil filter ensures that your system will operate at its peak efficiency and prevent short pollutants from clogging the oil-burner nozzle.

Step 5:- Change the Air Filter

Once you have successfully replaced the oil filter, it’s time to consider the air filter. However, before you change the air filter, be sure you brought the perfect air filter for your heating system. Keep in mind; every air filter is unique; hence it’s crucial to choose the right one that will adequately fit your heating system. We advise you to change the air filter; it’s always better to hire a professional expert and let them perform the task on your behalf.

Step 6:- Test the Burner Efficiency

By testing the burner efficiency, you will understand the boiler’s soot level and boiler’s draft pressure.

In order to measure the boiler efficiency, simply put a probe within the exhaust flue to extract the gas sample. Then, with a thermocouple, you can easily calculate the boiler efficiency.

 Conclusion

We have full faith that you can perform the Heating Installation & Repair on your own. However, where is the harm to hire the Best Heating Repair Services for your purpose? Besides, the heating system operates at a high temperature. Hence, if, without taking necessary precautions, you want to do this on your own, you might put yourself at big risk. Henceforth, opt for the assistance of JetAirCo Furnace & Boiler Installation, Maintenance, and Repair service center. Grab our help if you stay near Hauppauge, Smithtown, Northport, and Long Island, located in New York, USA

Meaning of Boiler Efficiency is the rate of how the boiler runs proficiently. The boiler is one of your home’s crucial components, working hard to keep you and your family warm. If you want to get warmth during the winter season, it’s essential to increase boiler efficiency. 

Remember that you should always opt for a reliable service provider like JetAirCo boiler installer service and let them perform the necessary tasks, including repairing, maintenance, and so on. However, there are specific tasks that you can perform on your own to ensure your boiler system stays in top form.

Practical Tips to Increase Boiler Efficiency:

Based on years of experience and customer reviews, the JetAirCo boiler installer service comes with some pocket-friendly techniques to increase your boiler efficiency.

 Inspect Your Heating System:

In order to increase the boiler efficiency, it’s crucial to turn on the heating system at least twice a month and on hot days as well. This process will help you to clean the boiler pump of any dust that might gather when the system is not in use.

Hence, turn on the heating system for at least 20-25 minutes per day. This will not only increase efficiency but also minimize the breakdown chance.

Schedule a Boiler Maintenance:

Bear in mind; even your boiler system operates fine, you still need to arrange an annual boiler service.  You can contact JetAirCo’s professionals for yearly maintenance.  Our technicians will recognize any issue and ensure that your system is running efficiently and smoothly.

Besides, annual maintenance will allow you to recognize issues at an early stage, and you can quickly fix the problem before it gets bigger. And of course, a small repair cost will be much lesser than a huge replacement cost.

Ensure Radiators Works Fine:

Besides the above two tips, you must regularly check and ensure that the radiators are working fine; if you experience cold spots, probably because of the trapped air. In this situation, hire a professional expert like JetAirCo and fix the issue instantly.  It will always be better to bleed the radiators before the winter months and make sure your boiler system will run when you need it most.

 Consider the Boiler Pressure:

Checking the boiler pressure is another effective strategy to increase boiler efficiency. If your system works properly, you will notice a reading between two bars. However, if you see the reading too low, then it’s time to hire a professional.

Adjust the Radiators:

Are the long-distance radiators colder than the near ones? If so, then you might have to balance the radiators.  Keep in mind balancing radiators isn’t a cup of tea, and you might need to call out a JetAirCo registered technician to complete this specific task.

Search for the Blue Flame:

If you can see the boiler flame, then check whether it’s a solid blue color or not. However, if you see an orange or yellow light, it means something happens wrong, and you must call out a professional expert as early as possible.

Avoid Blockage:

You have to wrap your boiler system properly to avoid blockage and increase efficiency.  However, don’t block the air vents as well as make sure that the outside flues are not blocked.

Cross Check the Condensate Pipe:

In a too cold climate, where the temperature drops below zero, the condensate pipe might freeze. And this can shut down your system and create a blockage. Fortunately, with some basic precautions, you can avoid the hassle.

 If you still haven’t installed the condensate pipe, JetAirCo suggests you wrap the pipes with old towels. This will also help the thermostat to provide the desired temperature.

Please leave the task to the JetAirCo Professionals

Whether you want to set a new boiler or increase its efficiency, the JetAirCo boiler installer service will be your ultimate choice. Our team of professionals can resolve any queries related to the boiler heating system. So, if you stay near Hauppauge, Smithtown, Northport, and Long Island, New York, call us today and check how we will fulfill your demands.

Millions of homeowners say that an electric boiler heating system is a more efficient and eco-friendly alternative to the traditional gas boiler. However, an electric boiler is more costly than a gas boiler as electricity is always expensive than natural gas.

Besides, a gas boiler lasts more than an electric boiler. Are you one of those homeowners who struggle to decide whether to choose a gas boiler or electric boiler? If yes, then the good news is for you as here the JetAirCo boiler repair service professional provides a short guide on electric boiler vs. gas boiler.

Definition of Gas Boiler:

A gas boiler burns gas to warm water for your house. Through pipes, the hot water is then moved to the radiators to provide heat. Besides, you can transport hot water via a cylinder or use water taps to get the hot water.

 Either by natural gas or liquid petroleum gas (LPG), you can turn on the gas boiler. The gas boiler comes with an underground network to fill fuel. However, the LPG boiler uses a cylinder to store fuels.

Definition of an Electric Boiler:

An electric boiler uses electricity and is directly supplied to the radiators, water taps, or cylinder to heat water.  Electric boiler provides fast work; however, it’s much expensive than a gas boiler. Hence, if you have a tight budget, JetAirCo boiler repair service professional suggests you opt for a gas boiler.

Electric Boiler Vs. Gas Boiler: Advantages and Disadvantages:

Let’s understand which boiler system will be perfect for your place. 

Gas Boiler:

Advantages :

  1. Repair and replacements are simple
  2. Inexpensive compared to electric boiler
  3. A gas boiler heating system is always available
  4. Can fulfill massive demand for heating and warm water
  5. 90 out of 100 homeowners rely upon a gas boiler.

Disadvantages :

  1. Many homeowners claim that installation is expensive.
  2. Not every house is connected to the gas grid network.
  3. There’s always a risk of gas leaks. Fortunately, you can avoid the risk if you complete the installation process with a professional expert, like JetAirCo.

Electric Boiler:

Advantages :

  1. There’s no need to place the electric boiler beside an outside wall as it doesn’t come with a flue or gas waste pipe.
  2. Not necessary to schedule annual maintenance.
  3. Compact in size
  4. set up process can be inexpensive
  5. Smooth operation

Disadvantages :

  1. Need to add extra functions that can be costly
  2. JetAirCo suggests installing an electric boiler might not be able to fulfill your all demands if you have a large home or residence.
  3. Electricity production can create a large amount of carbon.
  4. Power cuts can negatively impact the heating system.

Electric Boiler Vs. Gas Boiler: Installation and Running Cost

As per experts, the installation cost of a gas boiler is much lesser than an electric boiler.  However, it totally depends on the job complexity and your service provider.

Bear in mind, many factors decide the installation cost, like the price of the gas boiler or electric boiler itself. As said earlier, more gas boilers are available on the market.  Therefore, it’s possible to find an inexpensive gas boiler than an electric boiler.

Besides, gas boilers are typically less expensive to run. As per USwitch (an HVAC professional), a gas boiler can be up to 5 times less costly than an electric boiler.

Electric Boiler Vs. Gas Boiler: Energy Efficiency

Electric boilers consume less energy; hence many homeowners might believe that this type of heating system is more efficient.  However, it’s not true. An electric boiler produces a carbon-intensive, ultimately polluted environment more than a gas boiler.  On the other hand, if you properly use the gas boiler system, this can save up to 30 % of your energy bill.

Electric Boiler Vs. Gas Boiler: Annual Maintenance

The gas boiler needs annual maintenance to ensure that it operates at peak efficiency. Geeting, yearly maintenance from a reliable service, like JetAirCo, will always give you mental satisfaction.

On the other hand, an electric boiler doesn’t have such a requirement. This heating system is designed with fewer repairing components.

JetAirCo is here to help you

JetAirCo boiler repair service can help you decide which one will be most suitable for your place. A professional JetAirCo technician will provide you with the best heating system by making a partnership with famous brands. Hence, instantly contact us if you live near Hauppauge, Smithtown, Northport, and Long Island, New York.

As the environment changes and gets warmer, it’s the perfect time to focus on your heating system maintenance and get ready for the extreme heat of summer that surely lies ahead. And if you wish to get high-quality indoor air and feel relax, you must maintain your heating system each spring. Besides, daily maintenance can improve your system’s efficiency, save your precious time, money, and easily avoid the need for emergency repairs.

To well-maintain your heating system, you can take help from this guide and keep your family member comfortable and cool this summer.

1. Change the Air Filters:

If you continuously use your heating system, the air filter will fill with debris and dirt after a certain period of time. If this happens then, the air filter will clog up and decrease the airflow. As a result, your heating system will work harder in order to adjust your required temperature. Besides, a clogged filter will also increase the utility bills. On the other hand, if you replace the clogged filter, your system will consume less energy, save your money on energy cost, and improve the indoor air quality. In case you are not sure how to detect and change the air filter, stay on the safe side and call a professional technician.

Besides, you are advised to take off the AC unit to the outside. However, it’s a small step, but you have to do it. Keep in mind if the AC cover is left on, your heating system won’t be able to produce much air.

2. Clean the System Unit:

Always remember grime, dust, and dirt can accumulate around the heating system unit throughout the winter. This is another vital task that you should do before summer knocks on your door. Hence, clean the coils and remove all dust and debris from areas surrounding the unit. Keep an eye on the condenser unit and ensure there are no nests around the unit. You are also advised to register and sehedule for maintenance so the professional technician can check the condenser unit for any damage and perform the necessary repairs. You can thoroughly check out the outside part of the unit, and don’t ever try to open the unit on your own to avoid possible injuries. In addition, if you want to clean the condenser unit, the task must be performed by a professional.

3. Upgrade the Thermostat:

If your heating system won’t have a programmable thermostat, spring is the ideal time to buy. Also, when you set the thermostat to 78 degrees for 8 hours a day, you can even save up to 15 % on your heating and cooling bills per year. The purpose of the thermostat is to keep the temperature more comfortable during the day. In order to upgrade your thermostat, hire a professional and don’t walk into a hothouse anymore.

4. Seal the Air Duct Work:

Remember that if the air ducts are cleaned and sealed properly, your heating system will provide its peak performance in the warmer months and save you money.

5. Add a Heat Pump or air conditioner to your Heating System in Spring:

If you are searching for adding cooling to your heating system, the ideal time to do in spring. In the summer months, there will be a huge demand for heating systems. Hence the price will be higher at that time. Besides, you might have to wait for a couple of days as summer is the busiest season for the heating and cooling system. Hence, if you want to add an air conditioner or heat pump to your system, instantly call out a professional and install it on your device.

6. Inspect the Boiler and Furnace:

Due to numerous reasons, your boiler can stop working. Most of the time, if dirt and dust gather over the heating system, your boiler might stop responding. In order to properly maintain your furnace or boiler, first check if the issue can be repaired or not. If yes, then hire a professional technician and leave the rest of the task to them.

If you use the boiler for more than 10 years, we suggest replacing it with a new one. Spring is the best time to replace the boiler as, during the spring months, the prices will low, and you can easily afford the expenses.

7. Inspect Ventilation and Radiation:

Ventilation delivers heat to your house. On the other hand, radiation will heat the surrounding air. Sometimes, it might tap air within the radiation, and if it happens, the heating system unit doesn’t fill up with water. As a result, your system will consume more fuel and expend more energy to adjust the temperature.

In these circumstances, hire a heating system specialist who will check every point from which air enters your house. Besides, they will also make sure that ventilation and radiation work smoothly and the electronic system will thoroughly communicate with the rest of the system.

8. Make a Schedule for your Heating System Maintenance:

Always remember spring is the best season for heating system maintenance. When you work on your system on hot days, you are going to take risks. Therefore, book an appointment for your heating system maintenance and hire a professional technician to maintain your system well.

JetAirCo is here to help

At JetAirCo, we will maintain, repair, and replace any part of your heating system. Our technicians will analyze your problem first and give you the best solution to your problem. We provide our heating system maintenance service in Hauppauge, Smithtown, Northport, and Long Island. Call us today and get the best heating system maintenance and repair service in New York.

The solar heating system has come up with many benefits for saving your energy consumption cost, which is the prime thing for having a heating system. But, you cannot install a solar heating system as easily as you can install other types of systems. You need permission from your local authorities and neighbors. You are even asked to follow the building code for the installation. JetAirCo has been one of the old heating system repair service providers in New York. Although we have handled different heating systems, we are popular for furnace and boiler installation, heat pump services, and more. If you are not satisfied with your HVAC systems, you will get us by your side. Contact us to know more.

Here, we have discussed the things you need to complete beforehand for installing your solar heating system.

Due to the complex process, some households change their thoughts and opt for the regular ones for their comfort and luxury. Remember that a solar heating system is not only good for your saving but also the best option for nature and the environment. It uses renewable energy to heat your house.

You need to investigate your local building codes, zoning ordinances, and other special regulations attached to it. Obtain a building permit if you want to install the heating system on an existing building.

Many a time, community and municipality area impose some rules for installing the system. You may go through the tough process of obtaining permission. The installation is mainly a local issue, and you need to find a legal way to get this job done.

We are experienced in the field, and we want to make you aware of all the problems that you may experience with your solar heating system installation. Building codes are the most crucial thing in this case, and the common problems associated with it are:

  1. Exceeding roof load
  2. Wrong wiring
  3. Unacceptable heat exchangers
  4. Tampering with potable water supplies

You can consider special area regulations, including the local community, subdivisions, and homeowner’s association agreement. The best thing that you can do to avoid any legal issues is to contact your local jurisdiction’s zoning and building enforcement divisions and homeowner’s association.

You can contact us for your heating system installation process. We offer a wide range of services for your home heating systems. We offer gas furnace repair service, oil burner repair service, and other services for maintaining your systems.

You can contact us for more details. We have a main branch in Long Island, New York. But, we serve in other areas also, including Smithtown, Northport, and more.

Knowing your furnace always helps you take care of your system in a better way. Not all furnaces work the same. This is why you need to check the AFUE (Annual Fuel Utilization Efficiency) of your system. The higher the efficiency, the better your system works. If you need any help for maintaining your heating system, JetAirCo offers you the most satisfying service that quickly solves your heating system problems. We have an experienced team for your system maintenance. Since we have been in the fields for many years, we have earned the knowledge of handling different technologies. You will get the best heating system maintenance service in Smithtown, Long Island, Northport, and other areas.

Nearly every furnace has similar features, and the numbers go high or down as per the price. If you use a gas furnace, we have mentioned your furnace’s key factors and how they work. This detail will help you know more about your furnace.

Variable speed blowers:

Variable speed defines the furnace’s fan motor, which has a different speed to control the furnace’s heat.

Blower motor:

The blower motor helps the warm air passes through the ducts. It takes care of the cycling air process.

Air filtration:

With air filtration, you can improve the air quality coming from your furnace. An electrostatic filter is attached to your system to trap particles.

Heat exchanger:

In a heat exchanger, the air gets heated.

Venting:

Venting is a significant part of your furnace. It has pipes from the furnace to the outside, allowing the gases to go out of your house.

Zoned heating:

This heating system creates different zones or areas in your house for the heating. You can control these zones separately by using a thermostat. If you have a large home, the zone heating proves to very effective for you.

Your HVAC system enhances your comfort inside your house. So, they have a role to play in your happy life. If you experience any problem with your system, call JetAirCo. Issues in your HVAC systems can put your life in danger.

JetAirCo offers heating maintenance service in Smithtown, Northport, and in other areas of New York. Consult with our experienced professionals about your heating and cooling system.

Sometimes, your system just wants a replacement. You cannot detect the need because you are not aware of the problems your system may go through. An aging system is better to be replaced than repaired. There are some signs that your system gives before its complete breakdown. If your system needs frequent repairs, you can search for new systems.

If the energy bills are increasing every month, it denotes a problem with your heating system. You can have us checked the system to find out problems. Call JetAirCo for more details. We are always ready to serve your demands.

Everyone wants to have the most efficient home heating system for the house. It not only cuts down your energy cost but also keeps your environment safe, especially from the carbon footprint. If you want to buy the best heating system for your house, call a professional for advice. Remember that taking help from an HVAC professional service provider will always benefit you. Installing your heating system needs expert knowledge. So, hire a company that can help you find the best heating system for you.

JetAirCo is an HVAC service provider that fixes your problem quickly and enhances your home comfort in the best way. The company has a wide presence in areas like Hauppauge, Smithtown, Northport, and in more areas of New York

Choosing the right heating system is a necessary thing for your house. An HVAC expert can give you the right decision when it comes to the home heating system. There are various factors that determine which type of heating system you need.

As a buyer, you can gather knowledge about the efficiency rating of your heating system. AFUE (Annual Fuel Utilization Efficiency) is the measure that determines the amount of energy that is used by the heating system.

If you use a heat pump, HSPF instead of AFUE measures the efficiency of the heating system. SEER ratings are for measuring the efficiency of the heat pump in the cooling mode.

JetAirCo can help you get the best heating system for your home. We have a branch in Long Island, New York. But, our active areas are vast, including Hauppauge, Smithtown, North Port, and more. Our experienced heating system provider will visit your place and analyze your requirement to determine the best system for your space.

Picking the right type of heating system mostly depends on where you live. The climate is an essential factor for your heating system. We also consider your house built to choose the best system for you.

Heat pumps and furnaces are the two primary types of heating systems for residential use. We describe these systems to offer you a better idea of energy efficiency.

Heat pumps:

Heat pumps move the air using different methods to keep your house warm or cold, depending on your needs.  Air-source heat pumps bring down the temperature with the help of refrigerant. When you use the system in the heating mode, it extracts heat from the outside air. This type of heating system will work efficiently if you have moderate weather. But in freezing climates, this heating system does not work efficiently.

A geothermal heat pump uses the soil or water source to capture or release the heat. It is more efficient than the air-source heat pump. It reduces energy consumption and saves energy costs. But, it requires a higher installation charge.

Furnaces:

Furnaces are a common type of heating system. You can use gas, oil, or electricity to run your furnace. Gas furnaces are the cheapest ones, but they are not as efficient as air-source energy or electric furnaces. Check the AFUE rating and pick the higher one for better efficiency. JetAirCo will make your task easier by offering the best system for your house. We check your requirement and come up with the best system. If you need heating system services in Hauppauge, Smithtown, North Port, you can contact us. We will reach your place as soon as you contact us.

If you are worried about your furnace fan that is constantly running, there is nothing to be worried. Heating professionals believe that a continuous running of the furnace fan will benefit your heating. If you experience any odd things with your furnace, you can contact JetAirCo. The company is offering Heating Installation & Repair in Long Island, Northport, Smithtown, and in other places. Those who are using the furnace for heating, have the same questions to ask. Our heating experts will clear your doubts by sharing their experience.

When you keep the fan running always, you will get the better circulation of the heated air. Since the heat rises high, the upper portion seems hot and the lower area of your house remains comparably colder. To solve the issue, you must keep your furnace fan running always. It also helps the air circulate in every corner of the house.

It also benefits those who have problems with asthma, allergies, and respiratory problems. You can install an air filter to keep the quality of the air high. When you continually run the fan, it also improves the quality of the air.

JetAirCo is a trusted name for your HVAC system service. If you want heating repairs in Northport and other places, you can visit us to know more about our services. For immediate help, hire us and we take minimum time to reach your place.

When we are talking about the benefits of continuously running furnace fan, we must talk about some drawback also. It increases your electricity bill a bit. But, if you have a high efficient motor attached to it, you will experience no difference.

Many people even think that this continuous running of the furnace fan can cause a breakdown. But, you should know that manufacturers designed the fan for performing the function. It can bear the load and it does not cause any problems also.

Along with this, you have to keep in mind a few factors regarding your furnace fan. If your ductwork is located in the attic, you must not keep the fan running always. If you have leaky ductwork, you must keep your fan off when it is not needed.

The fan is continuously running because of the system of your thermostat. In most thermostat, there are two modes – auto and on. When you choose the auto mode, it turns on the fan as per the requirement. When it is on, the fan will always be running. It can also be caused by a faulty fan limit switch. If you experience a technical problem with your HVAC systems, you must call a professional for solving the issue.

JetAirCo is always there for you. It is offering Heating Installation & Repair in Long Island, Northport, Smithtown, and other parts in New York.

If you are using a gas furnace, you may be told to take extra precautions since gas furnaces create more unsafe situations compared to the other types. Sometimes, the concerns are exaggerated. Using gas for domestic and industrial purpose is very common. If your house has a natural gas line, you can do many things with it. You can also heat your furnace. If you are worried about the safety issue for your furnace, you must consult with a professional heating service. JetAirCo is a professional name that helps you repair your heating systems properly. We are offering HVAC maintenance and repair service in Smithtown, Northport, and Long Island. If you have any query regarding your heating system, we can solve your every problem.

 If you are thinking that gas furnace is unsafe to use. Time has come to check reality.

Here, we try to clear your doubts by presenting to you the facts of using a gas furnace.

Gas furnaces have safety measures:

These days, manufacturers introduce advanced safety measures to the gas furnaces to offer you a protected environment. You can get many built-in measures for your safety. So, thinking about the danger from your gas furnaces is wrong.

Carbon Monoxide Detector for Early Warnings:

Gas furnaces need a carbon monoxide detector to offer you a safe environment for your health. Carbon Monoxide (CO) is an odourless, colourless, and tasteless gas. This is why you need a detector that makes you alert about the amount of gas. These detectors are placed in different rooms and keep your living safe. These days, smoke alarm systems also come up with the CO detectors.

Routine maintenance:

Routine maintenance is required for your every HVAC appliance. Such maintenance should be carried out by experts because they are well-aware of the technical parts and they also take extra measures where the chances of faults are high. If you are using a gas furnace, a professional heating service provider pays attention to the heat exchanger and the gas lines. These are the most vulnerable areas when it comes to cracking and leakage. Hire JetAirCo for your heating system repair service. We are active in areas like Smithtown, Northport, and Long Island. Consult with our experts and come up with the right solutions for your HVAC systems.

Safety steps:

In the fall, your heater needs maintenance from the professionals. It improves the working condition of your heating system. In the winter, you also need to take extra maintenance steps for your heating system. Change the air filter in every 1 or 3 months. It prevents overheating. Clean the area around the cabinet and don’t keep any inflammable items around it.

JetAirCo is helping many houses for getting a comfortable temperature for your living. If you need any help for the maintenance of your HVAC system, we have a branch in Long Island, New York. Visit us for more details.  

You may not be aware of the type of heating system you have because you think it unnecessary. But, when your system gets stopped suddenly, you do all research to know about the system and to correctly describe the faults to a professional heating service provider. Knowing about your heating will not only help you to check the faults on your own, but you can also manage your system in a better way. This extends the life duration of your system and you can enjoy the comfort for a long time without any interruption. Contact JetAirCo for your heating maintenance, and you will also get instant service. They have a branch in Long Island, New York. But, their services are popular in areas like Hauppauge, Smithtown, Northport, and more.

You must know which type of heating system you have, and this knowledge will help you take care of your system in a better way.

Furnaces and heaters:

These systems generally use forced air process to heat your space and they are run by gas, propane, oil, or electricity. In the furnace, the air is heated and then is distributed into your rooms by ductwork. But, it is a tough decision to choose which fuel you want for your system. Call JetAirCo and get the right thing for your heating system. They are actively operating in areas like Hauppauge, Smithtown, Northport, and more.

Heat pump:

A heat pump is another popular version of your heating system, and it is commonly used in the moderate climate area. The system can be used for both heating and cooling your space as it moves heat from the cold place to the warm space, depending on your needs. It is basically a split system with both indoor cabinet and outdoor metal housing components. The system uses duct to distribute the heat, but you can opt for the ductless version also.

Call JetAirCo and find the right heating solution for your house. Our experienced heating professionals will always by your side. No matter which type of system you have, you will get a premium quality service from us. If you need a heating system service in Hauppauge, JetAirCo is near to you.

If you do not know whether you have a heat pump or an air conditioner, check the outdoor unit and you will get a label telling that it is a heat pump. If you find nothing on the unit, Google the model number and you will get detail about the system. Check the brass pipes also that reside in the condensing unit and these pipes are unique to the heat pump. If it also not works for you, check your thermostat for the emergency heating setting which is available for the heat pump only.

Geothermal heat pump:

You can also invest in the geothermal heat pump which is an energy-efficient option for heating your house. It uses natural heat from the earth to cool or warm air. Along with the benefits, some drawbacks of the systems are the high upfront cost and the disruption in the nearby landscape.

Boilers:

Boilers have two components – a furnace and a vessel where water turns into steam. This system can use electricity, natural gas, propane, and oil.

If you need a heating solution in New York, JetAirCo is the best place to visit. You can consult with our experienced professionals for your heating service. We are active in areas like Smithtown, Northport, Hauppauge, and Long Island.

If you use a gas furnace for heating your house, you should stay alert because it can cause dangerous situations for you and your family. The first thing that you need to do is to find the best and professional gas furnace fitters for you. They are experienced enough to install your heating system in the right way. Don’t try to fix the installation work on your own. One mistake can put you and your family in danger. JetAirCo is an experienced name for your heating system. It offers services in Long Island, Hauppauge, Smithtown, Northport, and in more areas.

When it comes to the gas furnace, an experienced name will always provide you with the right support. Remember that when you try to fix the installation, you know nothing about the technicalities. The chances of a faulty heating system become higher. It can catch fire in your house or can produce pollutant like carbon monoxide that is known as the silent killer. 

When you experience health issue while your heating system is on or your health issue gets worse, you must check your heating system to avoid any mishap. It can be the reason for the carbon monoxide released from your faulty heating system

Carbon Monoxide is a dangerous gas that does not have any color and odor. When you have a high level of carbon monoxide in the environment, it is so dangerous that it can take your life too. Children, pregnant women, aged people, and everyone exposed to the gas show serious health issues. If you are in such an environment, it shows you some signs, including:

  1. Tiredness
  2. Shortness of breath
  3. Dizziness 
  4. Headache
  5. Weakness
  6. Confusion
  7. Chest pain

If you have any symptoms mentioned above, your heating system may release carbon monoxide. Consult a doctor and get to know that whether your symptoms have any connection to the carbon monoxide or not. 

Gas heaters are essential as a home appliance. Always find an expert for installing your heating system. JetAirCo will help you install your system properly. We have an experienced team that reaches your house and analyzes your home environment. Then, we choose the right place for the installation. 

To protect you from any danger from the gas furnace, we mention some common signs of faults.

  1. You can find a yellow flame
  2. The pilot light bangs or goes out completely
  3. The discoloration of walls due to the heat damage
  4. The adjacent walls become too hot to touch
  5. Soot strains around the heater

All of these signs tell you that hire a professional heating service for your house. If you haven’t serviced your system for two years, you must immediately contact a heating system service provider near you. If you are in New York, we are with you. We are offering excellent heating system services in Long Island, Smithtown, Northport, and in many areas. 

A heating system will satisfy your needs when you choose the right system for your space. There are a few factors that you need to keep in mind while buying for a heating system. We talk about the efficiency of the systems and how you can choose the best ones. Everything depends on the technicalities of your heating system, and for this reason, you must contact an experienced heating system service provider. Contact JetAirCo and get the needed help for your heating system. We are a popular name for heating installation and repair in Hauppauge.

If you are looking for the best-centralized heating system for your house, you must consider the efficiency standard for your heating. We are discussing it in detail here.

Four criteria help you judge the efficiency and they are:

Fuel-burning Efficiency:

This involves flame efficiency. It checks the amount of the chemical energy in the fuel that gets converted into heat.

Steady-state efficiency:

It is also called combustion efficiency. It checks the heat transfer from the heat exchanger to the fluid. This checks the fuel-burning losses and chimney losses.

Actual Fuel Utilization Efficiency (AFUE):

This efficiency system checks the exact amount of fuel used by the system, accounting fuel-burning losses, chimney losses, stop/start cycling losses, and heat loss through the heating system.

Seasonal efficiency:

It measures the distribution loss in the duct walls.

Seasonal efficiency is the most reliable one for your heating system because it covers most areas of your heating system. But AFUE is the most used one. Those who buy a heating system always check the AFUE before buying. This rating system is labeled in your system also.

Get help from an experienced HVAC service provider for your heating system. They install your system in the right place and they help you use your system in the best way.

You can identify the working ability of your heating system with the AFUE. If you have an older, low-efficiency system, it uses a natural draft for bringing the combustion air but not in a perfect way. Here, the loss of combustion gasses happens through the chimney.

The low-efficiency system employs the combustion pilot light that burns fuel even without the need of the space. This system is bigger and heavier, and they lose energy in the extra cycling process.

A mid-level heating system comes up with the exhaust fan that channelizes the combustion air in the best way. It also includes the electronic ignition that eliminates the need for the pilot light, offering you more customized options for using your heating system.

The high-efficiency heating system can condense the flue gases to re-use the lost heat in the system. This is the most efficient one. Find the best HVAC system service provider for your heating system. You can contact JetAirCo and hire the best service for your system. We have the main branch in Long Island, New York, but we are offering services across New York.

If you have decided to install the heating system in your house, you need to prepare your property before. The installation work may damage your flooring, so you know what to expect from your system installation. To minimize the damage, you must call a professional for a pre-installation visit. Call JetAirCo and get your place checked by a professional team that has years of experience in the field. Contact heating system providers and make your place ready for installing a heating system. We have branches in Hauppauge, Smithtown, Northport, and more.

JetAirCo is an experienced name for your heating system. No matter what type of system you have, you can come up with the best solution. Contact JetAirCo and install a new heating system. Our team can help you in any type of heating system, including furnace, heat pumps, and more.

Here, we discuss what to do before installing your heating system:

Choose a type of heating system you have:

You must choose what type of heating system you want to install. Depending on which, other preparation will be done. Choose the type of boiler you want for your home. Consider your location, budget, and more details for choosing the best heating system for your house.

Find a space for the boiler:

Decide where you want to place your new boiler. Several things can change your decision. The boiler size and type are the most considerable things for finding a place.

Remove furniture and fragile items:

Before the work starts, you need to change the fragile items from the room where the installation work will be done. Cleaning the space help professionals to access your room rightly and you will get the right place for your system also. You can protect your valuable items from this damage also. One thing you need to remember that some types of flooring get damaged the installation more easily than the others. If you have laminate, linoleum, and vinyl flooring, you can decide on your heating system in the best way.

There are a few things that you can expect for your heating system and they are.

When you opt for the installation of your heating system, the work can be destructive. So, you need to hire the best heating system service provider for your work. They will check your place and come up with the right option for your system. Here, we want to make you aware of the damages that you can expect from your heating system.

Pooling up the flooring:

For the installation, experts can lift the flooring and can replace it with the new ones. It mostly depends on the type of flooring you have. Those who choose the underfloor heating, the floor will be raised with boards.

Concealing the pipes:

Some homeowners choose to conceal the pipes to unhurt the interior of the homes. This is an important step.

The new homeowners can save a lot of money by choosing the best heating system beforehand. It does not cause the damages also. Contact JetAirCo and find the best solution for your system. We have a branch in Long Island, New York.  We are also operating in areas like Hauppauge, Smithtown, Northport, and more.

Heating systems provide heat and it keeps you warm in chilling weather. There are 5 most common types of heating systems available in the market and we are talking about them here. If you are looking for the best system for your home, contact JetAirCo. The company has years of experience in the field of providing heating and cooling services to the household. We can help you pick the best heating system for your house.

Furnace:

A furnace is one of the most common types of heating systems for your house. It mainly works on the forced air concept where the air is heated by electricity, gas, propane, or oil. Then, the hot air keeps your room warm through the vents or the ductwork. The common places where you can find your system are basement, attic, or crawl space.

Heat pumps and geothermal heating system:

Heat pumps are very common in the moderate climate area and use electricity to move heat through the ducts. Heat pumps have two components – one stays outside and another one is kept inside of your house.

A geothermal heat pump is there to make your room warm and hot. It uses the earth’s temperature to heat or cool your room. It has no harmful emotion and it is energy-efficient also.

If you are confused about which system to buy, we recommend you call us for the best option. JetAirCo is offering heating services in Hauppauge, Smithtown, Northport, and more areas. Our branch is located in Long Island, New York.

Boiler heating system:

Boilers use the stored water to keep a space warm and it also uses oil, gas, electricity, and propane gas. Through the baseboard radiator and radiant heat floor systems, it keeps your room hot and warm.

Radiator heating system:

This is an old system and it comes up with a sealed container and it also has a boiler to heat your room.

Packaged unit heating system:

This type of heating system has both a heating and cooling unit. It stays on the roof of your house. It uses gas or electricity for heating and cooling your home. It heats your room through the ductwork.

Call JetAirCo and hire the best heating and cooling services for your house. We have a branch in Long Island, New York. We are also offering heating services in Hauppauge, Smithtown, Northport, and more.

When your heater suddenly stops, it is a reason for worry. You are probably searching for a possible answer to this problem. If you are not a technical person, you must call a professional heating service and solve your problem. Contact JetAirCo and find the right solution for your heating system. They are offering services in Hauppauge, Smithtown, Northport, and more.

A sudden stop of your heating system is a common problem and you can contact your nearest heating service provider for this. We discuss here some of the important notes for taking care of your system.

Furnaces manufactured after the 1990s have a safety switch or safety shut out. Whenever there is a technical error, your furnace will shut off. You have to solve the technical errors to turn on your heating system.

Here are some common technical errors that your system may have:

  1. Dirty evaporator coil
  2. Clogged pipes
  3. Full air filter
  4. Broken wires
  5. Dead blower motor

You need to contact the best HVAC company for solving the errors. JetAirCo is a renowned company and you can call them for repairing your system. They are offering heating services in areas – Hauppauge, Smithtown, Northport, and Long Island.

If there is no gas, your heater will not work. We all know that the central heating system can be run with different fuels, including gas, electricity, and water. People sometimes forget to turn on the power breaker switch. If the problem still persists, call JetAirCo and get a solution for your system. We have a branch in Long Island, New York.

Sometimes, the gas valve of your system gets stuck and this situation, your heating system will not work. You should not skip the maintenance work of your system. You can check the maintenance of your furnace.

Furnace maintenance can be effective. It solves all possible faults that stop your heating system. The maintenance of the furnace includes so many important factors.

JetAirCo offers a comprehensive maintenance process for your heating system.

We take care of every process for your system, including:

  1. Motors spin without resistance
  2. Clogged pipes
  3. Full air filter
  4. Broken wires
  5. Full air filters
  6. Burnt control board

If the entire system does not start properly, you must contact the best HVAC service provider and solve the issue. JetAirCo is an experienced name. The company is offering heating services in Hauppauge, Smithtown, Northport, and more. Book our services.

A power flush is required when your central heating system builds sludge in it and you do not get enough heating for your comfort. Whenever you feel that our system is not working properly, you can opt for the power flush for your central heating system. But, if you are looking for the exact answer to the question, you can opt for the power flush for every 5 to 6 years. Consult with an experienced HVAC service like JetAirCo. The company has a branch in Long Island, New York.

What is a power flush?

A power flush is nothing but a process of cleaning your central heating system. It is done through circulating the high volume of forced water along with the cleaning agents for clearing the debris. Contact JetAirCo and let them handle this process. Experienced professionals are there to take care of your system.

Here, we come up with a set of questions that help you to decide when the right time is for power flush for your central heating.

If you have new radiators, you no need to do the power flush. But, if you feel cold spots on the radiator, it is a sign of corrosion or sludge in your systems. This sludge may travel to your radiator and causes a cold spot. In this case, you need to do power flushing your system.

When your radiator is less than 4 years old:

If your radiator is less than 4 years old and you have a mild steel radiator and you are living in the hard water area, you will experience the normal rate of corrosion.

But when you have a stainless steel radiator and experience cold spots on the bottom of the radiator, it shows you a sign of faults. You can also check the boiler or plumbing of your heating system. Sometimes, the cold spot can be caused by them also. Hire an experienced professional team for heating service.

JetAirCo is offering heating services in Hauppauge, Smithtown, Northport, and in other areas. Contact the professional team and start repairing your system. Professionals, there are experienced in handling different types of systems and they are well aware of both modern and traditional components of the heating and cooling system.

When you have a 5 years old radiator:

If your radiator is 5 years old, you can opt for the power flushing to maintain your system. But, you can need this process of cleaning for every 8 to 10 years and that too depends on the material used in your system.

How do you know your system needs power flushing?

You can feel the bottom of the radiator and if you find a cold spot, you can opt for the power flushing option. Contact JetAirCo and hire an experienced heating system service provider. We offer services in the area of Hauppauge, Smithtown, Northport, and more. Our main branch is located in Long Island, New York.

Furnaces are a common component of your heating system. Although you do not require having this knowledge for having a heating system, knowing your furnace helps you identify any problem easily. JetAirCo is an experienced name for your heating system repair and installation service. We are offering HVAC services in areas like Hauppauge, Smithtown, Northport, and more.

A furnace heats the air that blows through the ducts and keeps your room warm by delivering heat to your home space through the registers and grills. This type of heating system is called a ducted warm-air or forced warm air system.

Inside a furnace, be it oil or a fuel-fired system, the fuel mixes with the air and it is then burnt. The flames heat a mental exchanger and the heat is transferred to the air. Then, the warm air is directed by the air handlers furnace fan and blows through the ductwork downstream of the heat exchanger.

The combustion products produced by the furnace is then blown through the flue pipes and released out of the house. The older atmospheric furnaces vented the combustion out in the atmosphere directly and it loses nearly 30% of energy.

The newer version heating systems use the energy the best. They are efficient enough to reuse the heat from the combustion. The old version uses energy to keep the exhaust warm enough for the safe rise in the chimney. The high-efficiency furnace even condenses water vapor in the exhaust into water.

In the U.S., the efficiency of the furnace is measured by the standard AFUE (Annual Fuel Utilization Efficiency). AFUE marks the seasonal efficiency, averaging peak, and more. It also takes care of the other factors like electricity used by your heating system, its start-up time, cool-down time, and other operating losses, and more.

So, a furnace has many complex jobs to do. If it has problems, it shows in the heat production and you will not get a comfortable temperature. JetAirCo is an experienced name in the field. Your heating system is an important part of your indoor luxury.

Contact JetAirCo and book heating services. We are very much active in Hauppauge, Smithtown, Northport, and more. Tell us your problem and our service provider will visit your place. They are experienced in different segments of heating systems – gas boiler, water boiler, heat pumps, furnaces, and more. Contact us.

Heating systems provide relief from chilling cold. But, you have to make smart choices to lower your utility bills by choosing an efficient system for your house. JetAirCo is an experienced HVAC system repairing service provider. We are offering heating system services in Hauppauge, Smithtown, North Port, and long Island. If you want a consultation, we are always with you.

Most of the houses have a heating system for keeping the indoor air warm during the winter season. Some people use furnace whereas some people use boilers for their homes. Here, we are mentioning how the boiler works and keeps your home a comfortable place in the winter season.

A boiler uses water to heat and then either hot water or the steam passes through the pipes and radiators to keep a space warm. Most of the systems used by the homeowners are water heating boilers. Some old houses have a steam heating system. JetAirCo mentions that both the heating systems are good when it comes to heating your home.

If you need a heating repair system service in Hauppauge, Long Island, North Port, and in other areas of New Work, JetAirCo is the best place to visit. Give us a call and expert professionals will visit you for repairing your system. Our professional team is experienced in different heating systems, including heat pumps and other systems.

If you have a boiler, it definitely sits on top of the burner to burn the fuel for producing heat. The most common fuel used in the U.S is natural gas. The gas is supplied by a provider through the pipes that run across the street and roads. In the rural areas, propane gas is used instead of natural gas, and that gas is stored in a large tank in the yard of the house. To make you remind that propane is expensive than natural gas.

In the U.S, some households use a boiler that is heated by oil. Oil boilers are very rate in that sense and many such boilers have been converted to natural gas or propane gas boilers. Both natural gas and propane gas boiler are a cheaper option than the heating oil.

If you want to choose the best option for your house, contact JetAirCo. The company has years of trust in the field and is offering HVAC services for many years. If you are living in New York, we can assure you that you will always have us by your side. Give us a call and book our heating system repair or installation service.